About
Control Unit
• Input voltage: AC 200–240 V
• Frequency: 50/60 Hz
• Fuse: 2 A
• Output current: 2 A
• Rotation speed: up to 35,000 rpm
• Weight: 1.5 kg
• Dimensions: 163.4 × 125.3 × 67 mm
Handpiece
• Power: 80 W
• Rotation speed: up to 35,000 rpm
• Torque: 3.0 N·cm
• Weight: 250 g
• Dimensions: length 146 mm, diameter 13.8–27.5 mm
Operation
• Before use, make sure the control unit is switched off and connect the device to the power supply.
• Connect the control unit to the handpiece and place the handpiece in its holder.
• Ensure that the bur is properly locked in the chuck.
• After completing the above steps, switch on the control unit.
• Slowly turn the speed control knob to gradually increase the rotation speed.
• Select hand or foot control mode to check proper operation.
• Set the rotation direction to forward or reverse.
Note
Before starting the micromotor, turn the handpiece in the direction indicated by the arrow to lock the bur. Turning it in the opposite direction unlocks the chuck and allows the bur to be replaced.
Important Safety Precautions
• Use the device only in dry and well-ventilated areas.
• Do not operate the device in hazardous environments.
• The handpiece, foot pedal, and control unit must be original and compatible with each other.
Operating Conditions
• Temperature: 10–40 °C
• Relative humidity: 30–75%
• Atmospheric pressure: 700–1060 hPa
Bur (Bit) Requirements
• Recommended shank diameter: 2.35 mm
• Diameters of 3.0 mm and 3.175 mm are also permitted in accordance with ISO 7785-2 Type 2
• Do not use rusty or deformed burs
• Always follow the manufacturer’s recommended operating speeds and safety guidelines
• When using needle burs, strictly comply with the specified diameter and speed requirements
Warning
• Recommended bur insertion depth into the chuck: 27–30 mm.
• The longer the exposed part of the bur, the greater the centrifugal force, which reduces rigidity and increases the risk of deformation.
• Using large-diameter burs at high speeds may cause serious damage, including:
- bur bending (which may result in finger injuries),
- bearing damage,
- chuck deformation,
- other equipment malfunctions.
Warranty
12 months from the date of purchase
Control Unit
• Input voltage: AC 200–240 V
• Frequency: 50/60 Hz
• Fuse: 2 A
• Output current: 2 A
• Rotation speed: up to 35,000 rpm
• Weight: 1.5 kg
• Dimensions: 163.4 × 125.3 × 67 mm
Handpiece
• Power: 80 W
• Rotation speed: up to 35,000 rpm
• Torque: 3.0 N·cm
• Weight: 250 g
• Dimensions: length 146 mm, diameter 13.8–27.5 mm
Operation
• Before use, make sure the control unit is switched off and connect the device to the power supply.
• Connect the control unit to the handpiece and place the handpiece in its holder.
• Ensure that the bur is properly locked in the chuck.
• After completing the above steps, switch on the control unit.
• Slowly turn the speed control knob to gradually increase the rotation speed.
• Select hand or foot control mode to check proper operation.
• Set the rotation direction to forward or reverse.
Note
Before starting the micromotor, turn the handpiece in the direction indicated by the arrow to lock the bur. Turning it in the opposite direction unlocks the chuck and allows the bur to be replaced.
Important Safety Precautions
• Use the device only in dry and well-ventilated areas.
• Do not operate the device in hazardous environments.
• The handpiece, foot pedal, and control unit must be original and compatible with each other.
Operating Conditions
• Temperature: 10–40 °C
• Relative humidity: 30–75%
• Atmospheric pressure: 700–1060 hPa
Bur (Bit) Requirements
• Recommended shank diameter: 2.35 mm
• Diameters of 3.0 mm and 3.175 mm are also permitted in accordance with ISO 7785-2 Type 2
• Do not use rusty or deformed burs
• Always follow the manufacturer’s recommended operating speeds and safety guidelines
• When using needle burs, strictly comply with the specified diameter and speed requirements
Warning
• Recommended bur insertion depth into the chuck: 27–30 mm.
• The longer the exposed part of the bur, the greater the centrifugal force, which reduces rigidity and increases the risk of deformation.
• Using large-diameter burs at high speeds may cause serious damage, including:
- bur bending (which may result in finger injuries),
- bearing damage,
- chuck deformation,
- other equipment malfunctions.
Warranty
12 months from the date of purchase
Nail Drill Machine Ülka Flow
SKU:NDM_UF
- Regular price
- €197,20
- Sale price
- €197,20
- Regular price
-
€281,70